Toshiba GX9 ASD Скачать руководство пользователя страница 41

Страница: 41 / 100

GX9 ASD Quick Start Guide

System Configuration and Menu Options

Root Menus

The

Mode

key accesses the three primary modes of the

GX9 ASD

: the

Frequency

Command

mode, the

Monitor

mode, and the

Program

mode. From either mode, press the

Mode

key to loop through to the

other two modes (see

Figure 24

). While in the

Frequency Command

mode, pressing the

ESC

key

toggles the menu to and from the

Command (RS232/RS485)

menu and the

Frequency Command

mode.

Note:

Parameter changes made from the

Command (RS232/RS485)

menu are effective for

Local

LCD

EOI

control

Only

Figure 24. Root menu mapping.

Frequency Command Mode

Frequency Setting

While operating in the

Local

mode (Local LED is illuminated on the front panel), the running frequency

of the motor may be set from the

Frequency

Command

screen. Using the

Rotary Encoder

, enter the

Frequency Command

value and then press the

Run

key. The motor will run at the

Frequency

Command

speed and may be changed while running.

Содержание GX9 ASD





































































































Результаты поиска

Содержание GX9 ASD

Отзывы:

Бренды по названию

Популярные бренды

Toshiba GX9 ASD, Быстрый старт

Результаты поиска

Содержание GX9 ASD

Отзывы:

Бренды по названию

Популярные бренды