Toshiba G2020 Series Скачать руководство пользователя страница 26

Страница: 26 / 86

G2020 Series UPS Installation and Operation Manual

– 94861-004

Table 3-5 Specifications

Rated Output kVA

500

750

Rated Output kW

500

750

AC INPUT

Configuration

3 phase, 3 wire

Voltage

480 V +15% to -20%

Frequency

60 Hz ±10%

Reflected Current THDi

3% typ. at 100% load (no input filter required)

STATIC BYPASS INPUT

Configuration

3 phase, 3 wire

Voltage

480 V ±10%

Frequency

60 Hz ±5%

ENERGY STORAGE

Type

Lead Acid, SCiB Lithium Titanate (LTO)

Ride Through

Application Specific

Nominal Voltage

480 Vdc

Minimum Voltage

400 Vdc

Number of Cells

VRLA: 240, SCiB: Application Specific

AC OUTPUT

Configuration

3 phase, 3 wire

Voltage

480 V

Voltage Regulation

±1%

Frequency

60 Hz

Frequency Regulation

±0.01% in free running mode

Power Factor

Unity (nominal)

Power Factor Range

0.7 Lagging to 0.8 Leading (within output kW rating)

Voltage THD

2% maximum THD at 100% linear load
5% maximum THD at 100% non-linear load

Transient Response

±2% maximum at 100% load step
±1% maximum at loss/return of AC power
±5% maximum at load transfer to/from static bypass

Transient Recovery Time

Less than 20ms

Voltage Unbalance

1% maximum at 100% unbalanced load

Phase Displacement

1 deg. maximum at 100% Load

Inverter Overload

125% for 1 minutes
150% for 10 seconds

Bypass Overload

500% for 1 cycle
(with bypass available)

ENVIRONMENTAL**

Cooling

Forced Air

Operating Temperature



F to 104



F (0



C to 40



C).

Recommended : 68

ﾟ

F to 86

ﾟ

F ( 20



C to 30



Relative Humidity

– 95% Non-Condensing

Altitude

0 to 6500 ft. (1981 m) No Derating at 104

ﾟ

F (40

ﾟ

Location

Indoor (free from corrosive gases and dust)

Paint Color

Munsell N1.5 (Black)

Clearance Required

Top : 24 in. (610 mm)
Front : 40 in. (1016 mm)
Rear : 0 in. (0 mm)
Sides: 0 in. (0 mm) if sidecars used, 1 in. (25 mm) if no sidecars used.

**Indication that the unit is intended for installation in a temperature-regulated,
indoor area that is relatively free of conductive contaminants.

Содержание G2020 Series























































































Результаты поиска

Содержание G2020 Series

Отзывы:

Toshiba G2020 Series, Инструкция по установке и эксплуатации, Страница: 26 / 86

Результаты поиска

Содержание G2020 Series

Отзывы: