Toshiba EB621 Скачать руководство пользователя страница 64

Страница: 64 / 122

model 2000 Ethernet Module Operation Manual

Chapter 4 Installation and Wiring

4.3 Drop Cable Connection for Line B Modules

Use the following combinations of modules in an Ethernet system of dual transmission
line configuration.

• 10BASE5: EN621 (main module) + EB621 (line-B module)

• 10BASE2: EN641 (main module) + EB641 (line-B module)

Connect a main module to a line B module with a twisted pair cable. Do not combine
modules other than specified above.

(1) Connect a twisted pair cable to the line-B module drop cable connector (CN1) on the

line-B module. The twisted pair cable connector is an 8P modular connector.

(2) Connect the twisted pair cable from the line-B module to the line-B module drop

cable connector (CN1) on the main module.

(3) Insert the module connector fully till it clicks and check that the connector has been

locked.

Figure 4-7 Line-B Module Drop Cable Connection

Warning

• Do not connect the 10BASE-T or other interface to the modular connector by mistake. Oth-

erwise, it may cause not only product trouble but also smoke and a fire.

EN6 module
or
EB6 module

Drop cable for
line-B module

･

Standard: 70 mm

･

Maximum: 3 m

Drop cable connector
for line-B module
(CN1)

Содержание EB621



























































































































Результаты поиска

Содержание EB621

Отзывы:

Бренды по названию

Популярные бренды

Toshiba EB621, Руководство по эксплуатации

Результаты поиска

Содержание EB621

Отзывы:

Бренды по названию

Популярные бренды