Toshiba e-STUDIO557 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 180

Toshiba e-STUDIO557 Скачать руководство пользователя страница 30

2 HOW TO MAKE COPIES

28 Placing Originals

Continuous feed mode

The feeding mode is set at “continuous feed mode” by default. Once you set the originals and then press the
[START] button, they are scanned page by page continuously. It is useful when you want to copy more than
one original at one time.

1

Align all the originals.

Collate the originals in the order that you want them to be copied. The top sheet of the originals will be
copied first.

When there are too many originals to be scanned at one time, divide the originals into several sets before
copying. Place the first set of the originals and then press [CONTINUE] on the touch panel while the data
of this set are being scanned. When this scanning is finished, place the next set of the originals and press
the [START] button on the control panel. (If you press [CONTINUE] just before the originals finish being
scanned, this button may not work.)

2

Place the originals with their face up and align the
side guides to the original length.

y

Originals up to 100 sheets (35 to 80 g/m

2

(9.3 to 20 lb.))

16 mm (0.62") in height are acceptable regardless of their
sizes.

y

For mixed-size originals, see the following page:

P.52 “Copying mixed-size originals in one operation”

For long originals

Pull out the original stopper so that the scanned original will not
fall off.

After the original stopper was used, lift it slightly and push it
in.

«
...
28
29
30
31
32
...
»

Содержание e-STUDIO557





















































































































































































Отзывы:

Нет отзывов