manualshive.com logo in svg

Toshiba e-STUDIO557, Руководство по копированию

Поделиться
Скачать
Toshiba e-STUDIO557 Скачать руководство пользователя страница 19

1.BEFORE USING EQUIPMENT

Placing Paper    17

1 BEFORE USING EQUIPMENT

„

Placing paper in the tandem large capacity feeder

y

Paper in the right-hand tray is used first. When it runs out, paper in the left-hand tray will be 
moved automatically to the right-hand tray and fed.

y

A maximum of 2500 sheets (80 g/m

2

) (20 lb. Bond) can be placed in the 2 trays. However the 

stack height of the paper must not exceed the line indicated inside the side guides.

 

 P.11 “Acceptable copy paper”

y

The copy side may be noted on its wrapping paper.

y

Be careful not to cut your fingers when fanning the paper.

y

When placing paper, be sure that the center lever is not open. (See the label attached in the 
drawer of the tandem large capacity feeder.)

3

Push the drawer of the tandem large capacity feeder straight into this equipment 
carefully.

When the drawer is completely inserted, the right-hand tray will move up to the paper feeding position.

Be careful not to let your fingers be caught when pushing the drawer into this equipment. 

This could injure you.

1

Pull out the drawer of the tandem large capacity 
feeder carefully until it comes to a stop.

Be careful not to touch the slide rails (A in the figure).

This could injure you.

2

Place 2 stacks of paper in the right and left trays 
correspondingly.

Fan and jog the paper well before placing it. Place it with its 
copy side down. Place one stack of paper in the right-hand tray 
(shown as “A” in the figure) with its side touching the right 
corner of the tray, and place the other stack of paper in the left-
hand tray (shown as “B” in the figure) with its side touching the 
left corner of the tray. Paper can be placed neatly if you divide 
stacks into small bundles and pile them up on the two trays 
alternately.

A

A

B

A

Содержание e-STUDIO557





















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды