manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 55 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 55

3

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

SELF-DIAGNOSTIC MODE

3 - 31

Remarks: 

In the USB storage procedure above, lists are stored in a CSV format. The names of the CSV 
files are shown below.
201: ADJUSTMENT_LIST_serial_date and time(YYYYMMDDHHMMSS).csv
202: SETTING_LIST_serial_date and time(YYYYMMDDHHMMSS).csv
204: PIXEL_TONER_LIST_serial_date and time(YYYYMMDDHHMMSS).csv
205: PIXEL_SERVICE_LIST_serial_date and time(YYYYMMDDHHMMSS).csv
206: ERROR_LOG_serial_date and time(YYYYMMDDHHMMSS).csv
208: FW_UPGRADE_LOG_serial_date and time(YYYYMMDDHHMMSS).csv
210: POWER_ONOFF_LOG_serial_date and time(YYYYMMDDHHMMSS).csv
211: VERSION_LIST_serial_date and time(YYYYMMDDHHMMSS).csv
214: TOTAL_COUNTER_LIST_serial_date and time(YYYYMMDDHHMMSS).csv
221: 05DIFFERENCE_CODE_LIST_serial_date and time(YYYYMMDDHHMMSS).csv
222: 08DIFFERENCE_CODE_LIST_serial_date and time(YYYYMMDDHHMMSS).csv
223: JOB_LOG_serial_date and time(YYYYMMDDHHMMSS) (encrypted file)/MESSAGE_LOG_ 
serial_date and time(YYYYMMDDHHMMSS) (encrypted file)
224: FAX_FUNCTION_LIST_Serial No._Date(YYYYMMDDHHMMSS).csv

3.13.2

List Printing

Lists below are output in the list print mode.
List data are printed out or output in a CSV format by storing them in a USB device. Paper sizes 
available for this printing are A4 or LT or larger. This section introduces a sample of each list.
To start the list print mode, turn the power on while pressing [9] + [START] button.

*1: (05) adjustment value difference and (08) setting value difference are not output.
*2: Since the Job log/Message log file obtained is encrypted, you cannot read it.

Lists

List code

Printout

CSV file output

Adjustment mode (05) data list

101

201

Setting mode (08) data list

102

202

Pixel counter list (toner cartridge 

reference) 

104

204

Pixel counter list (service call reference)

105

205

Error history list

106

(Maximum 1000 items)

206

(Maximum 1000 items)

Error history list

107

(Latest 80 items)

-

Firmware upgrade log

108

(Maximum 200 items)

208

(Maximum 200 items)

Power ON/OFF log

110

(Maximum 100 items)

210

(Maximum 100 items)

Version list

111

211

Total counter list

114

214

(05) adjustment value difference 

121

221

(08) setting value difference

122

222

Job log / Message log  

*2

-

223

FAX Function mode (13) data list

-

224

Output all CSV files

-

300 

*1

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов