manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 307 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 307

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

FIRMWARE UPDATING

8 - 19

8

8.3.1

Writing the data to the download jig (PWA-DWNLD-JIG2)

The download jig (PWA-DWNLD-JIG2) is that in which the Flash ROM is mounted on the board directly. 
The ROM writer adapter (PWA-DL-ADP-350) is required to write data to these Flash ROMs. Connect 
the download jig with the ROM writer via ROM writer adapter to write data. For the procedure to write 
data, refer to the downloading procedure, instruction manual of each ROM writer, or other sources.

Fig.11-2

[1] PC
[2] Download jig (PWA-DWNLD-JIG2)
[3] ROM writer adapter (PWA-DL-ADP-350)
[4] ROM writer

Notes: 

There are two types of the ROM writer adapter. Use the proper one according to the ROM writer 
to be used. Applicable type of the adapter for the ROM writer can be confirmed by the model 
name indicated on the board. Confirm that the adapter is available for the ROM writer to be used 
before connecting them. If an unapplied adapter is connected, the application of the ROM writer 
judges it as an error and writing the data cannot be implemented. Applicable combinations of the 
ROM writer and adapter are as follows.

ROM writer

ROM writer adapter

Minato Electronics MODEL 1881XP/
1881UXP
(or equivalent)

PWA-DL-ADP-350-1881 (model 1881)

Minato Electronics MODEL 1893/1895/
1931/1940
 (or equivalent)

PWA-DL-ADP-350-1931-LV640 (model 1931)

Fig.8-13

Fig.8-14

[1]

[2]

[4]

[3]

model   1881

[PWA-DL-ADP-350-1881]

model   1931

(LV650)

[PWA-DL-ADP-350-1931-LV640]

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов