Toshiba e-Studio477s Скачать руководство пользователя страница 201

Страница: 201 / 482

e-STUDIO477S/527S/477SL

ERROR CODE AND TROUBLESHOOTING

5 - 97

[71B5] Finisher firmware installation failure

[7261] SU firmware installation failure

[7263] SU Loader installation failure

[7265] SU Recovery installation failure

[7267] PU firmware installation failure

[7269] PU Loader installation failure

Classification

Error item

Maintenance error

Finisher firmware installation failure

Check item

Measures

Setting

Finisher firmware installation failed. Reinstall the firmware.

Classification

Error item

Maintenance error

SU firmware installation failure

Check item

Measures

Setting

SU firmware installation failed. Reinstall the firmware.

Classification

Error item

Maintenance error

SU Loader installation failure

Check item

Measures

Setting

SU Loader installation failed. Reinstall the firmware.

Classification

Error item

Maintenance error

SU Recovery installation failure

Check item

Measures

Setting

SU Recovery installation failed. Reinstall the firmware.

Classification

Error item

Maintenance error

PU firmware installation failure

Check item

Measures

Setting

PU firmware installation failed. Reinstall the firmware.

Classification

Error item

Maintenance error

PU Loader installation failure

Check item

Measures

Setting

PU Loader installation failed. Reinstall the firmware.

Содержание e-Studio477s


























































































































































































































































































































































































































































































Результаты поиска

Содержание e-Studio477s

Отзывы:

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 201 / 482

Результаты поиска

Содержание e-Studio477s

Отзывы: