manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 160 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 160

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

ERROR CODE AND TROUBLESHOOTING

5 - 56

[F106_1] ADI-HDD error: HDD type detection error

[F106_2] ADI-HDD error: ADI encryption key download operation error

HDD

• Connector check
• Harness check
Follow the procedure below if no abnormality is found in the 
check items above.

1. Start the equipment in the 4C mode: [4] + [C] + 

[POWER] -> 1. Revert factory initial status HDD

2. Reinstall the system software.

If the error persists even after above step, replace the HDD. 
If the equipment operation disabled after above step, 
replace the HDD.

Classification

Error item

Other service call

ADI-HDD error: HDD type detection fails. 

Check item

Measures

Setting

If the error is not recovered after rebooting the equipment 
or no abnormality is found on any check items for the HDD, 
reinstall the system software. 

HDD

• Connector check
• Harness check
• Start the equipment in the 5C mode: [5] + [C] + 

[POWER] 
Check the file system and recover it if necessary.
If the recovery fails, replace the HDD.
If the equipment does not start in the 5C mode, also 
replace the HDD.

• Check that either the ADI-HDD or SATA-HDD (normal 

type) is mounted.

1. Start the equipment in the 4C mode: [4] + [C] + 

[POWER]

2. Check the type of the HDD shown on the top left of the 

control panel display "Current HDD type". 
Normal status: ADI-HDD or SATA-HDD
Abnormal status: Unknown HDD

If "Unknown HDD" is displayed, reinstall the system 
software.
If the error persists even after above step, replace the HDD. 
If the equipment operation disabled after above step, 
replace the HDD.

Classification

Error item

Other service call

ADI-HDD error: Downloading of or consistency check for ADI-
HDD encryption key fails.

Check item

Measures

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов