Toshiba E-Studio 5540c Скачать руководство пользователя страница 57

Страница: 57 / 118

1 TROUBLESHOOTING FOR THE HARDWARE

Replacing the Waste Toner Box 55

Replacing the Waste Toner Box

When the waste toner box becomes full, the symbol for replacement of the waste toner box blinks and the message
“Dispose of used toner” appears. Replace the waste toner box following the procedure below.

Never attempt to incinerate waste toner boxes.

Dispose of used toner cartridges and waste toner boxes in accordance with local regulations.

Separate the finisher from the equipment when it is installed.

1) Open the front cover of the finisher when the Hole Punch Unit is not installed. Open the Hole Punch Unit cover

when the Hole Punch Unit is installed.

2) Pull the lever to unlock the finisher.

3) Move the finisher until it stops putting your hands on the positions shown in the figure.

Press the button on the waste toner box cover to
open it.

Take out the waste toner box.

When the Hole Punch Unit is not installed

When the Hole Punch Unit is installed

When the Hole Punch Unit is not installed

When the Hole Punch Unit is installed

Содержание E-Studio 5540c























































































































Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды

Toshiba E-Studio 5540c, Руководство по устранению неисправностей

Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды