Toshiba E-Studio 5540c Скачать руководство пользователя страница 36

Страница: 36 / 118

1 TROUBLESHOOTING FOR THE HARDWARE

34 Clearing a Paper Jam

Receiving tray lower cover

Separate the finisher from the equipment when it is installed.

1) Open the front cover of the finisher when the Hole Punch Unit is not installed. Open the Hole Punch Unit cover

when the Hole Punch Unit is installed.

2) Pull the lever to unlock the finisher.

3) Move the finisher until it stops placing your hands on the positions shown in the figure.

Close the cover under the receiving tray.

Using the handle under the receiving tray, open the
cover and remove the paper.

Close the covers of the finisher and the Hole Punch
Unit (when it is installed) first, and connect the
finisher to the equipment.

Move the finisher slowly placing your hands on the positions shown
in the figure.

Be careful not to let your fingers be caught between the
finisher and the equipment

When the Hole Punch Unit is not installed

When the Hole Punch Unit is installed

When the Hole Punch Unit is not installed

When the Hole Punch Unit is installed

Содержание E-Studio 5540c























































































































Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды

Toshiba E-Studio 5540c, Руководство по устранению неисправностей

Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды