background image

- 19 -

1. Image System

Image Device

Pixel Elements

2. Electrical

TV System

Horizontal Resolution

S/N Ratio

Minimum Illumination

Auto Gain Control (AGC)

Iris Control Mode

White Balance

White Balance Range

Gamma compensation

Backlight Compensation (BLC)

Video Output Signal

Synchronization System

3. Mechanical

Weight

Dimension

4. Optical

Built-in Lens

View Angle

Focus Length

5. Power

Input Voltage

Power Consumption

6. Environmental

Operating Temperature

1/3 inch CCD image sensor

768 (H) x 494 (V)

2:1 Interlace, 15.734 KHz horizontal, 59.94 Hz
vertical

520 TV lines

50 dB

0.5 lux (More than 10 % of image output,
Smoke cover)

Average AGC

Auto Iris Lens

Auto

2,500 K to 10,000 K

0.45

ON / OFF (DIP-SW)

VBS (1.0 Vp-p, 75 ohms unbalanced, BNC)

Line Lock, Internal manually switchable

0.738 lbs (360 g)

ø5.08 (D) x 3.94 (H) inches (ø129 (D) x 100 (H)
mm)

Varifocal lens
f = 2.8 ~ 10 mm, F 1.3 : Auto Iris

Wide : 129 

°

(D), 100 

°

(H), 73 

°

(V)

Tele : 34 

°

(D), 27 

°

(H), 20 

°

(V)

0.3 m ~ 

24V AC +

- 10 % 60 Hz / 12V DC +

- 10 %

3.5 W

14 

°

F to 122 

°

F (-10 

°

C to +50 

°

C), 20 % to

90 % RH

10. SPECIFICATIONS

Design and specifications are subject to change without notice.

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Содержание DF02A - Day/Night Mini-Dome Color Camera CCTV

























Отзывы: