Toshiba B-SX4T Series страница 223 Скачать руководство пользователя | Manualshive

Страница: 223 / 374

background image

- 219 -

6.3.26 SAVE START COMMAND

(For ATA Card)

[ECS]

XV

Function

Declares the start of saving PC interface commands.

(Places the printer in the mode where PC interface commands are written in the ATA
card.)

Format

[ESC] XV; dddddddd, b, c [LF] [NUL]

Term

dddddddd:

Identifier to be used for saving in the ATA card or calling

File name using from 1 to 8 characters

Available

characters:

A to Z:

A to Z (in both upper and lower case)

0 to 9:

Numerals from 0 to 9

Symbols: !, ”, #, $, %, &, ’, ), (, -, ^, _, {, }, ¯

b:

Drive
1: Slot 1 on the PCMCIA board (Option)
2: Slot 2 on the PCMCIA board (Option)

c: Status response at save time

0: No status response made
1: Status response made

Explanation

(1) When the PC interface command is stored in the ATA card, directory “PCSAVE” is

created, and then the directory “Specified file name. PCS” is created under the
“PCSAVE” directory level.

(2) Up to about 1 MB can be saved per a save.

Notes

(1) After sending the Save Start Command ([ESC] XV), any command other than the

following will be saved into the ATA card without being analyzed.

•  Save Start Command ([ESC] XO)
•  Save Terminate Command ([ESC] XP)
•  Saved Data Call Command ([ESC] XQ, [ESC] XT)
•  Bit Map Writable Character Command ([ESC] XD, [ESC] XA)
•  Reset Command ([ESC] WR)
•  Status Request Command ([ESC] WS)
•  Flash Memory Format Command ([ESC] J1)
•  ATA Card Format Command ([ESC] JA)

(2) No error check is made for the commands at save time.

Refer to

• Save Terminate Command ([ESC] XP)

• Flash Memory Format Command ([ESC] JA)

Examples

[ESC] JA; B [LF] [NUL]

[ESC] XV; PC_SAVE, 1, 0 [LF] [NUL]

[ESC] D0508, 0760, 0468 [LF] [NUL]

[ESC] T20C30 [LF] [NUL]

[ESC] C [LF] [NUL]

[ESC] PC001; 0200, 0125, 1, 1, A, 00, B [LF] [NUL]

[ESC] PC002; 0650, 0550, 2, 2, G, 33, B, +0000000001 [LF] [NUL]

[ESC] XP [LF] [NUL

«
...
221
222
223
224
225
...
»

Содержание B-SX4T Series























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B-SX4T Series

T15 Mifare Reader Black

Бренд: Gallagher Страницы: 13

Бренд: Custom Audio Electronics Страницы: 16

Бренд: Chase Страницы: 8

Бренд: Duerkopp Adler Страницы: 116

Бренд: Iseo Страницы: 2

ViVOpay VP3300 Series

Бренд: IDTECH Страницы: 20

Бренд: Follett Страницы: 2

Бренд: Axicon Страницы: 24

Бренд: SimpleTech Страницы: 7

Бренд: TSC Страницы: 42

TTP-244CE series

Бренд: TSC Страницы: 44

Бренд: TSC Страницы: 49

Бренд: CIRCLE Страницы: 7

Бренд: CIRCLE Страницы: 10

Бренд: Mirano Страницы: 17

Бренд: RIOTEC Страницы: 2

Бренд: RIOTEC Страницы: 2

Бренд: RIOTEC Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды