background image

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
Precautions for Handling of Wireless Communication Devices 
Bluetooth® Module: BT800  
Wireless LAN Module: RS9113 
 
Trade Mark 

Bluetooth  is  a  registered  trademark  owned  by  Bluetooth  SIG,  Inc.  and  used  byTOSHIBA  TEC  CORPORATION  under 
license.  
 

Cautions 

 

General 

For all countries and areas 
This  product  is  a  wireless  communication  device,  and  the  use  of  this  product  is  restricted  to  the  following  countries  or 
areas. If the product is used in the countries or areas other than the following, you may be punished according to the laws 
of those countries or areas. 
USA, Canada, Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, 
Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, 
Slovenia, Spain, Sweden, United Kingdom, Switzerland, Norway, Iceland, Liechtenstein, Australia, New Zealand

 

 
 

For Europe 

For Bluetooth and Wireless LAN: 
Hereby, TOSHIBA TEC CORPORATION declares that the BT800 and RS9113 are in compliance with the essential 
requirements and other relevant provisions of Directive 2014/53/EU. This equipment uses a radio frequency band that has 
not been harmonized throughout all EU and EFTA countries, and can be used EU and EFTA countries. 
 

For USA 

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: 
(1) this device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that may cause undesired operation. 
 
Changes or modification not expr

essly approved by manufacturer forcompliance could void the user’s authority to operate 

the equipment. 
 

For Canada 

Operation is subject to the following two conditions: 
(1) this device may not cause interference, and 
(2) this device must accept any interference, including interference that may cause undesired operation of the device. 
 
To  prevent  radio  interference  to  the  licensed  service,  this  device  is  intended  to  be  operated  indoors  and  away  from 
windows to provide maximum shielding. Equipment that is installed outdoors is subject to licensing. 

 

Without  permission,  any  company,  firm  or  user  shall  not  alter  the  frequency,  increase  the  power,  or  change  the 
characteristics and functions of the original design of the certified lower power frequency electric machinery.  
The  application  of  low  power  frequency  electric  machineries  shall  not  affect  the  navigation  safety  nor  interfere  a  legal 
communication, if an interference is found, the service will be suspended until improvement is made and the interference 
no longer exists. 
 

For safety 

Do not use this product in locations where use may be forbidden, for example,in an aeroplane or a hospital. If you do not 
know the forbidden areas, please refer to and follow the airline company or medical institution guidelines. 
Flight instruments or medical equipment may be affected, causing a serious accident. 
 
Since this product uses extremely low power compared  with mobile phones,  it cannot possibly interfere the pacemakers 
and  defibrillators.  However,  if  the  use  of  this  product  should  be  likely  to  have  affected  the  pacemaker  or 
defibrillator,immediately stop using the product and contact your TOSHIBA TEC sales agent. 
 
Do not disassemble, modify, or repair the product.  Doing so may cause injury. Also, modification is against the  Laws and 
Regulations for Radio Equipment. Please ask your TOSHIBA TEC sales agent for repair. 
 

Precaution in use 

This product communicates with other devices by radio. Depending on the installation location, orientation, environment, 
etc., its communication performance may deteriorate or devices installed near by may be affected. 

Содержание B-FP3D-GH52-QM-R

























Отзывы: