background image

 

12 

6.2  LED  FUNCTION 

[ONLINE] LED 

Indicates that the printer is in online state. 

Flashes when the printer is communicating with the host. 

Flashes  (ON:  250ms.  OFF:  250ms.)  in  synchronization  with  the  ERROR  LED 

when the printer is turned off. 

Flashes in the power save mode (ON: 1 sec., OFF: 1 sec.) (Note) 

[ERROR] LED 

Indicates that the printer is in error state. 

Flashes  when  a  ribbon  near  end  condition  is  detected  (at  a  1-second  interval 

(ON: 500ms. OFF: 500ms.) 

Flashes when a system error occurs (ON: 500ms. OFF: 500ms.) 

Flashes  (ON:  250ms.  OFF:  250ms.)  in  synchronization  with  the  ONLINE  LED 

when the printer is turned off. 

Note:  If the wireless LAN is being linked when the printer is off, both the ONLINE and ERROR LED just turns 

on, not flash.     

 

 

6.3  LCD  FUNCTION 

The LCD displays the messages which indicate the printer status. 

LCD 

Type 

Graphics LCD 

Size 

128 dots (W) x 64 dots (H) 

Display structure 

Maximum of 21 digits x 5 lines 

 

 

6.4  ONLINE  MODE  SCREEN 

6.4.1  Online  Mode  Screen  Example   

Printer 

condition 

LCD 

Description of each line 

Online 

 

B-EX4T1

C1.6

PRINTED

000000

IP:192.168.010.020

ONLINE

 

 

 
← Model name, Firmware version (*5) 
← Message 
← The number of labels printed (*1) 
← IP address etc. (*4) 
← Icon 

Pause 

 

(TO DO) 123

PAUSE

 

 

 
← The number of remaining labels to print (*2) 
← Message 
← 1

st

 line of the error message 

← 2

nd

 line of the error message (*6) 

← Icon 

Head open 

 

(TO DO) 123

Close the print
head block.

Help▶

HEAD OPEN

 

 

 
← The number of remaining labels to print (*2) 
← Message 
← 1

st

 line of the error message 

← 2

nd

 line of the error message 

← Icon, Help guide (*3) 

 

Содержание B-EX6T Series

































































































































































Отзывы: