background image

20 

Introduction

synchronization to quadruple the TV refresh rate for an even clearer 

fast motion video. See 

“ClearScan™” on page 101

.

 

DynaLight™

—Backlight control monitors the brightness of each 

video frame and automatically adjusts backlight intensity based on 

the content to create higher dynamic contrast, for deeper blacks and 

increased depth. See 

“DynaLight™” on page 101

.

 

AutoView™

—Allows you to automatically adjust picture settings 

including Brightness, Contrast, Gamma, and Sharpness based 

on ambient room light conditions and incoming picture content 

to create the best possible picture settings without any manual 

adjustment.

 

MediaShare

—Allows you to view photo files and play music or 

movie files, see 

“MediaShare (Videos, Music, and Photos)” on page 

141

.

 

Cloud Portal

—Enhanced content discovery includes real time 

streaming news, true social interaction features, and mobile device 

interaction. See 

“Using the Cloud Portal Service features” on page 

135

.

Overview of installation, setup, and use

Follow these steps to set up your TV and begin using its many exciting 

features.

Carefully read the important safety, installation, care, and service 

information. Keep this manual for future reference.

To choose a location for the TV:

 

Read 

“Important notes about your TV” on page 7

.

 

Place the TV on a sturdy, level, stable surface that can support 

the weight of the unit. Secure the TV to a wall, pillar, or other 

immovable structure, see 

24)

 on page 4.

 

Place the TV in a location where light does not reflect on the 

screen.

 

Place the TV far enough from walls and other objects to 

allow proper ventilation. Inadequate ventilation may cause 

overheating, which will damage the TV. THIS TYPE OF 

DAMAGE IS NOT COVERED UNDER THE TOSHIBA 

LIMITED WARRANTY.

Do not plug in any power cords until after you have connected all 

cables and devices to your TV.

 

Overview of installation, setup, and use

Содержание 55L7400U

























































































































































































Отзывы: