background image

Specifications

Note:

Specifications and design are subject to change without notice.

Base weight

Dry 544 kg (1,200 lb)

Rated capacity (on level ground)

749 kg (1,650 lb) total, including 90.7 kg (200 lb) operator and
90.7 kg (200 lb) passenger, load, trailer tongue weight, gross
trailer weight, accessories, and attachments

Maximum gross vehicle weight (GVW)—on level ground

1,292 kg (2,850 lb) total, including all of the weights listed above

Maximum cargo capacity (on level ground)

567 kg (1,250 lb) total, including trailer tongue weight and gross
trailer weight

Tow capacity:

Standard hitch

Tongue weight 45 kg (100 lb) Maximum trailer weight 363 kg
(800 lb)

Heavy-duty hitch

Tongue weight 45 kg (100 lb) Maximum trailer weight 544 kg
(1,200 lb)

Overall width

150 cm (59 inches)

Overall length

303 cm (119.3 inches)

Ground clearance

25 cm (10 inches) at the front with no load or operator, 18 cm
(7 inches) at the rear with no load or operator

Wheel base

206 cm (81 inches)

Wheel tread (center line to center line)

125 cm (49 inches) in the front, 120 cm (47-1/4 inches) in the rear

Cargo bed length

117 cm (46 inches) inside, 133 cm (52-1/4 inches) outside

Cargo bed width

125 cm (49 inches) inside, 150 cm (59 inches) at outside of the
molded fenders

Cargo bed height

25 cm (10 inches) inside

Attachments/Accessories

A selection of Toro approved attachments and accessories is available for use with the machine to enhance
and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a
list of all approved attachments and accessories.

14

 

Содержание Workman 07235





























































Отзывы: