Toro TX 427 22342HD Скачать руководство пользователя страница 48

Страница: 48 / 52

Troubleshooting

Problem

Possible Cause

Corrective Action

1. The battery is discharged.

1. Charge the battery or replace it.

2. The electrical connections are

corroded or loose.

2. Check the electrical connections for

good contact.

The starter does not crank.

3. The relay or switch is damaged.

3. Contact your Authorized Service

Dealer.

1. The fuel tank is empty.

1. Fill the fuel tank with fuel.

2. The choke is not on.

2. Move the choke lever fully forward.

3. The air cleaner is dirty.

3. Replace the air-cleaner element.

4. The spark-plug wires are loose or

disconnected.

4. Install the wires on the spark plugs.

5. The spark plugs are pitted, fouled, or

the gap is incorrect.

5. Install new, correctly gapped spark

plugs.

6. There is dirt in the fuel filter.

6. Replace the fuel filter.

The engine does not start, starts hard, or
fails to keep running.

7. Dirt, water, or stale fuel is in fuel

system.

7. Contact Authorized Service Dealer.

1. The engine load is excessive.

1. Reduce the ground speed.

2. The air cleaner is dirty.

2. Replace the air-cleaner element.

3. The oil level in crankcase is low.

3. Check and add oil to the crankcase.

4. The cooling fins and air passages

under the engine blower housing are
plugged.

4. Remove any obstructions from the

cooling fins and air passages.

5. The spark plugs are pitted, fouled, or

the gap is incorrect.

5. Install new, correctly gapped spark

plugs.

6. There is dirt in the fuel filter.

6. Replace the fuel filter.

The engine loses power.

7. Dirt, water, or stale fuel is in fuel

system.

7. Contact Authorized Service Dealer.

1. The engine load is excessive.

1. Reduce the ground speed.

2. The oil level in crankcase is low.

2. Check and add oil to the crankcase.

The engine overheats.

3. The cooling fins and air passages

under the engine blower housing are
plugged.

3. Remove any obstructions from the

cooling fins and air passages.

There is abnormal vibration.

1. The engine mounting bolts are loose.

1. Tighten the engine mounting bolts.

1. The parking brake is on.

1. Release the parking brake.

2. The hydraulic-fluid level is low.

2. Check and add hydraulic fluid.

3. The tow valves are open.

3. Close the tow valves.

The traction unit does not drive.

4. The hydraulic system is damaged.

4. Contact Authorized Service Dealer.

Содержание TX 427 22342HD





















































Результаты поиска

Содержание TX 427 22342HD

Отзывы:

Похожие инструкции для TX 427 22342HD

Бренды по названию

Популярные бренды

Toro TX 427 22342HD, Руководство оператора

Результаты поиска

Содержание TX 427 22342HD

Отзывы:

Похожие инструкции для TX 427 22342HD

Бренды по названию

Популярные бренды