Toro TRX-16 Скачать руководство пользователя страница 16

Specifications

Note:

Specifications and design are subject to change

without notice.

Width

86 cm (33.8 inches)

Length, with 70 cm (24
inch) boom

209.5 cm (82.5 inches)

Length, with 91.4 cm (36
inch) boom

235 cm (92.6 inches)

Length, with 122 cm (48
inch) boom (model 22974
only)

282.5 cm (111.2 inches)

Height

117 cm (46 inches)

Weight (model 22972)*

499 kg (1,100 lb)

Weight (model 22973)*

538 kg (1,185 lb)

Weight (model 22974)*

578 kg (1,208 lb)

* A 91.4 cm (36 inch) boom and chain will add about 27 kg (60 lb) to the listed weight.

Attachments/Accessories

A selection of Toro approved attachments and accessories is
available for use with the machine to enhance and expand
its capabilities. Contact your Authorized Service Dealer or
Distributor or go to www.Toro.com for a list of all approved
attachments and accessories.

Operation

Note:

Determine the left and right sides of the machine

from the normal operating position.

Important:

Before operating, check the fuel and oil

level, and remove debris from the machine. Also, ensure
that the area is clear of people and debris. You should
also know and have marked the locations of all utility
lines.

Recommended Fuel

For best results, use only clean, fresh (less than 30 days
old), unleaded gasoline with an octane rating of 87 or
higher ((R+M)/2 rating method).

Ethanol:

Gasoline with up to 10% ethanol (gasohol)

or 15% MTBE (methyl tertiary butyl ether) by volume
is acceptable. Ethanol and MTBE are not the same.
Gasoline with 15% ethanol (E15) by volume is not
approved for use.

Never use

gasoline that contains more

than 10% ethanol by volume, such as E15 (contains 15%
ethanol), E20 (contains 20% ethanol), or E85 (contains
85% ethanol). Using unapproved gasoline may cause
performance problems and/or engine damage which may
not be covered under warranty.

Do not

use gasoline containing methanol.

Do not

store fuel either in the fuel tank or fuel containers

over the winter unless a fuel stabilizer is used.

Do not

add oil to gasoline.

DANGER

In certain conditions, gasoline is extremely
flammable and highly explosive. A fire or explosion
from gasoline can burn you and others and can
damage property.

Fill the fuel tank outdoors, in an open area,
when the engine is cold. Wipe up any gasoline
that spills.

Never fill the fuel tank inside an enclosed trailer.

Do not fill the fuel tank completely full. Add
gasoline to the fuel tank until the level is 6 to 13
mm (1/4 to 1/2 inch) below the bottom of the
filler neck. This empty space in the tank allows
gasoline to expand.

Never smoke when handling gasoline, and stay
away from an open flame or where gasoline
fumes may be ignited by a spark.

Store gasoline in an approved container and
keep it out of the reach of children. Never buy
more than a 30-day supply of gasoline.

Do not operate without entire exhaust system in
place and in proper working condition.

16

Содержание TRX-16





















































Отзывы: