Toro TITAN HD 1500 Скачать руководство пользователя страница 70

Страница: 70 / 88

Controls System
Maintenance

Adjusting the
Control-Handle Position

If the ends of the levers hit against each other, refer to

Adjusting the Motion-Control Linkage (page 71)

Adjusting the Height

You can adjust the motion control levers higher or
lower for maximum comfort.

Disengage the blade-control switch (PTO), move
the motion-control levers to the N

EUTRAL

LOCK

position, and engage the parking brake.

Shut off the engine, remove the key, and wait
for all moving parts to stop before leaving the
operating position.

Remove the hardware holding the control lever
to the control-arm shaft.

g035858

Figure 103

Bolts

Control lever

Slotted hole

Control-arm shaft

Move the control lever to the next set of holes.
Secure the lever with the hardware.

Repeat the adjustment for the opposite control
lever.

Adjusting the Tilt

Disengage the blade-control switch (PTO), move
the motion-control levers to the N

EUTRAL

LOCK

position, and engage the parking brake.

Shut off the engine, remove the key, and wait
for all moving parts to stop before leaving the
operating position.

Loosen the upper bolt holding the control lever
to the control arm shaft.

Loosen the lower bolt just enough to pivot the
control lever fore or aft. Tighten both bolts to
secure the control in the new position.

Repeat the adjustment for the opposite control
lever.

g009195

Figure 104

Содержание TITAN HD 1500

























































































Результаты поиска

Содержание TITAN HD 1500

Отзывы:

Toro TITAN HD 1500, Руководство оператора, Страница: 70 / 88

Результаты поиска

Содержание TITAN HD 1500

Отзывы: