Toro TITAN HD 1500 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 88

background image

g029685

Figure 81

Kohler engine filter shown

5.

Open the fuel-shutoff valve.

Servicing the Fuel Tank

Do not attempt to drain the fuel tank. Ensure that an
Authorized Service Dealer drains the fuel tank and
services any components of the fuel system.

Electrical System
Maintenance

Electrical System Safety

•

Disconnect the battery before repairing the
machine. Disconnect the negative terminal first
and the positive last. Connect the positive terminal
first and the negative last.

•

Charge the battery in an open, well-ventilated
area, away from sparks and flames. Unplug the
charger before connecting or disconnecting the
battery. Wear protective clothing and use insulated
tools.

Servicing the Battery

Service Interval:

Monthly

Removing the Battery

WARNING

Battery terminals or metal tools could short
against metal machine components, causing
sparks. Sparks can cause the battery gasses
to explode, resulting in personal injury.

•

When removing or installing the battery,
do not allow the battery terminals to touch
any metal parts of the machine.

•

Do not allow metal tools to short between
the battery terminals and metal parts of the
machine.

1.

Park the machine on a level surface, disengage
the blade-control switch (PTO), and engage the
parking brake.

2.

Shut off the engine, remove the key, and wait
for all moving parts to stop before leaving the
operating position.

3.

Disconnect the negative (black) ground cable
from the battery post (

).

Note:

Retain all fasteners.

59

«
...
57
58
59
60
61
...
»

Содержание TITAN HD 1500

























































































Отзывы:

Нет отзывов

Похожие инструкции для TITAN HD 1500

Бренд: Yard force Страницы: 25

Бренд: Cub Cadet Страницы: 19

LazerCut LCS405

Бренд: SANLI Страницы: 19

Бренд: Villager Страницы: 128

Бренд: Jacobsen Страницы: 104

Бренд: Lastec Страницы: 51

Бренд: Simplicity Страницы: 52

Бренд: Toro Страницы: 36

Бренд: Ferris Страницы: 60

Бренд: Qualcast Страницы: 2

Бренд: Gardena Страницы: 290

Бренд: Black+Decker Страницы: 12

Бренд: ECLOZ Страницы: 56

Бренд: Troy-Bilt Страницы: 40

Бренд: ARNETOLI MOTOR Страницы: 2

Бренд: Poulan Pro Страницы: 48

Бренд: Poulan Pro Страницы: 30

Бренд: Poulan Pro Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды