manualshive.com logo in svg

Toro TimeCutter ZS 3200S, Руководство оператора

Поделиться
Скачать
Toro TimeCutter ZS 3200S Скачать руководство пользователя страница 38

Releasing the Electric Brake

The electric brake can be release by manually rotating the
link arms forward. Once the electric brake is energized the
brake will reset.

To release the brake:

Figure 47

1.

Brake link arm on the electric brake control module

2.

Left rear tire

1.

Turn the ignition key to the Off position or disconnect
the battery.

2.

Locate the shaft on the electric brake where the brake
link arms are connected.

3.

Rotate the shaft forward to release the brake.

Mower Maintenance

Servicing the Cutting Blades

Maintain sharp blades throughout the cutting season, because
sharp blades cut cleanly without tearing or shredding the grass
blades. Tearing and shredding turns grass brown at the edges,
which slows growth, and increases the chance of disease.

Check the cutter blades daily for sharpness, and for any
wear or damage. File down any nicks and sharpen the
blades as necessary. If a blade is damaged or worn, replace
it immediately with a genuine Toro replacement blade. For
convenient sharpening and replacement, you may want to
keep extra blades on hand.

WARNING

A worn or damaged blade can break, and a piece
of the blade could be thrown into the operator's
or bystander's area, resulting in serious personal
injury or death.

•

Inspect the blade periodically for wear or
damage.

•

Replace a worn or damaged blade.

Before Inspecting or Servicing the
Blades

Park the machine on a level surface, disengage the
blade-control switch, move the motion-control levers outward
to the park position, stop the engine, and remove the key.

38

 

Содержание TimeCutter ZS 3200S

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды