Toro TimeCutter Z530 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 44

background image

Electrical System

Maintenance

Servicing the Battery

Check the electrolyte level in the battery every
25 hours. Always keep the battery clean and fully
charged. Use a paper towel to clean the battery
case. If the battery terminals are corroded, clean
them with a solution of four parts water and one
part baking soda. Apply a light coating of grease
to the battery terminals to prevent corrosion.

Voltage: 12 V

Removing the Battery

Battery terminals or metal tools could short
against metal machine components causing
sparks. Sparks can cause the battery gasses
to explode, resulting in personal injury.

•

When removing or installing the battery,
do not allow the battery terminals to
touch any metal parts of the machine.

•

Do not allow metal tools to short between
the battery terminals and metal parts of
the machine.

1. Park the machine on a level surface and

disengage the blade control switch.

2. Move the motion control levers to the brake

position, stop the engine, remove the key, and
wait for all moving parts to stop before leaving
the operating position.

3. Tip the seat forward to see the battery.

4. Disconnect the negative (black) ground cable

from the battery post (Figure 32).

Incorrect battery cable routing could
damage the machine and cables causing
sparks. Sparks can cause the battery
gasses to explode, resulting in personal
injury.

•

Always disconnect the negative
(black) battery cable before
disconnecting the positive (red)
cable.

•

Always connect the positive (red)
battery cable before connecting the
negative (black) cable.

5. Slide the rubber cover up the positive (red)

cable. Disconnect the positive (red) cable from
the battery post (Figure 32).

6. Remove the battery hold-down (Figure 32) and

lift the battery from the battery tray.

Figure 32

1. Battery

4. Negative battery cable

2. Terminal boot

5. Battery hold-down

3. Positive battery cable

6. Bolt, nut, and washer

27

«
...
25
26
27
28
29
...
»

Содержание TimeCutter Z530













































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter Z530

Бренд: Lux Tools Страницы: 140

Бренд: Gravely Страницы: 36

Бренд: Bush Hog Страницы: 1

Бренд: Ryobi Страницы: 340

Бренд: Neuton Страницы: 56

Бренд: P.I.T. Страницы: 23

Бренд: Troy-Bilt Страницы: 52

Бренд: Cramer Страницы: 180

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды