Toro REELMASTER 6700 D Скачать руководство пользователя | Manualshive

Страница: 31 / 56

background image

Maintenance Service

Interval

Maintenance Procedure

Every 400 hours

• Service the air cleaner. (more frequently in extremely dirty or dusty conditions).

Service the air cleaner earlier if the air-cleaner indicator shows red.

• Check the fuel lines and connections for deterioration, damage, or loose connections

(or yearly, whichever comes first).

• Replace the fuel-filter canister.
• Check the planetary gear drive oil (also, check if external leakage is observed).
• Check the rear axle lubricant level.

Every 800 hours

• Change the planetary gear drive oil (or yearly, whichever comes first).
• Change the rear axle lubricant.
• Check the rear wheel toe-in.
• If you are not using the recommended hydraulic fluid or have ever filled the reservoir

with an alternative fluid, change the hydraulic fluid.

• If you are not using the recommended hydraulic fluid or have ever filled the reservoir

with an alternative fluid, replace the hydraulic filter.

Every 1,000 hours

• If you are using the recommended hydraulic fluid, replace the hydraulic filter.

Every 2,000 hours

• If you are using the recommended hydraulic fluid, change the hydraulic fluid.

Every 2 years

• Drain and clean the fuel tank.
• Drain and flush the cooling system.

Daily Maintenance Checklist

Duplicate this page for routine use.

For the week of:

Maintenance Check Item

Mon.

Tues.

Wed.

Thurs.

Fri.

Sat.

Sun.

Check the safety-interlock operation.

Check the brake operation.

Check the engine oil and fuel level.

Drain the water/fuel separator.

Check the air-filter-restriction indicator.

Check the radiator and screen for debris.

Check unusual engine noises.

1

Check unusual operating noises.

Check the hydraulic-fluid level.

Check the hydraulic-filter indicator.

2

Check hydraulic hoses for damage.

Check for fluid leaks.

Check the tire pressure.

Check the instrument operation.

Check the reel-to-bedknife adjustment.

Check the height-of-cut adjustment.

Check all grease fittings for lubrication.

3

Touch-up damaged paint.

1. Check the glow plug and injector nozzles if hard starting, excess smoking, or rough running is noted.

2. Check with the engine running and the oil at operating temperature.

3. Immediately after every washing, regardless of the interval listed

31

«
...
29
30
31
32
33
...
»

Содержание REELMASTER 6700 D

























































Отзывы:

Нет отзывов

Похожие инструкции для REELMASTER 6700 D

Бренд: Lawn-Boy Страницы: 32

Бренд: Ybravo Страницы: 16

Бренд: EGO Страницы: 2

Бренд: Racing Страницы: 21

Бренд: ZIPPER MASCHINEN Страницы: 65

Бренд: P.Lindberg Страницы: 36

Бренд: Parker Страницы: 25

Бренд: Yard-Man Страницы: 4

Бренд: Snapper Страницы: 18

Бренд: Honda Страницы: 20

Stockman 4000 A16314E

Бренд: COX Страницы: 50

Бренд: Poulan Pro Страницы: 48

Бренд: Gearmore Страницы: 27

Бренд: Royal Страницы: 64

Бренд: Black & Decker Страницы: 40

Бренд: Black & Decker Страницы: 17

Бренд: Black & Decker Страницы: 16

Бренд: Black & Decker Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды