Toro Reelmaster 5510 Series Скачать руководство пользователя страница 494

Страница: 494 / 662

Removing the Wheel

1. Park the machine on a level surface, lower the cutting units, shut off the

engine, set the parking brake, and remove the key from the key switch.

2. Block the wheels that are not removed with chocks to prevent the machine

from moving.

3. Loosen, but do not remove the 5 wheel-lug nuts that attach the wheel to

the machine.

IMPORTANT

Before lifting the machine with a jack, review and follow

Jacking

Instructions (page 1–6)

4. Lift the machine with a jack until the wheel to be removed is off the ground.

Support the machine with appropriate jack stands.

5. Remove the 5 wheel-lug nuts that attach the wheel to the machine, and

remove the wheel.

Installing the Wheel

1. Install the wheel to the machine with the 5 wheel-lug nuts.

2. Lower the machine to the ground.

WARNING

Failure to maintain proper torque could result in failure or loss of
wheel and may result in personal injury.

Maintain the proper torque of the wheel-lug nuts.

3. Torque the wheel-lug nuts evenly to

95 to 122 N∙m (70 to 90 ft-lb)

in a

crossing pattern.

4. Check and adjust the tire pressures; refer to

Specifications (page 8–2)

Chassis: Service and Repairs

Page 8–6

Reelmaster

5410/5510/5610 Series

15216SL Rev C

Содержание Reelmaster 5510 Series























































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Reelmaster 5510 Series

Отзывы:

Toro Reelmaster 5510 Series, Руководство по обслуживанию, Страница: 494 / 662

Результаты поиска

Содержание Reelmaster 5510 Series

Отзывы: