Toro Reelmaster 5510 Series Скачать руководство пользователя страница 266 | Manualshive

Страница: 266 / 662

Toro Reelmaster 5510 Series Скачать руководство пользователя страница 266

Flushing the Hydraulic System (continued)

IMPORTANT

If a component failure occurs in the traction circuit; refer to the

Traction Circuit Component Failure (page 6–9)

for information

regarding the importance of removing contamination from the
traction circuit.

1. Ensure that the hydraulic fluid is at normal operating temperature by

operating the machine for at least 20 minutes.

CAUTION

Before opening the hydraulic system, operate all the hydraulic
controls to release system pressure and avoid injury from the
pressurized hydraulic fluid; refer to

Releasing Pressure from the

Hydraulic System (page 6–8)

.

2. Park the machine on a level surface, lower the cutting units, shut off the

engine, set the parking brake, and remove the key from the key switch.

Note:

Ensure that you clean all the hydraulic connections that are

disconnected for draining.

3. Drain the hydraulic fluid from the hydraulic tank. Remove the tank cap,

screen filter, and clean the tank. Consider removing and cleaning the
reservoir if necessary.

4. Clean the area around the mounting areas of the hydraulic-fluid filters.

Remove and replace the hydraulic-fluid filters.

5. Inspect and clean the hydraulic tank; refer to

Inspecting the Hydraulic Tank

(page 6–155)

.

IMPORTANT

Follow all local codes and regulations when recycling or disposing
hydraulic fluid and filters.

6. Drain the complete hydraulic system. Drain all the hoses, tubes, and

components while the system is warm. Flush the hoses and tubes to remove
any contamination.

7. Connect all the hydraulic hoses, tubes, and components that were

disconnected while draining the system.

8. Ensure that the mounting surfaces of the hydraulic-fluid filters are clean.

Apply clean hydraulic fluid to the gasket on new filters. Tighten the filters until
the gasket contacts the mounting plate, then tighten the filter 3 quarters
of a turn.

IMPORTANT

Using other hydraulic fluids could damage the hydraulic system.
Use the hydraulic fluids that are specified in the

Operator’s Manual

.

Hydraulic System: Service and Repairs

Page 6–148

Reelmaster

®

5410/5510/5610 Series

15216SL Rev C

«
...
264
265
266
267
268
...
»

Содержание Reelmaster 5510 Series























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов