background image

Form No. 3362-558 Rev A

Power Max

®

Snowthrowers

Model No. 38624—Serial No. 310000001 and Up

Model No. 38634—Serial No. 310000001 and Up

Model No. 38644—Serial No. 310000001 and Up

Model No. 38654—Serial No. 310000001 and Up

Operator's Manual

Introduction

This snowthrower is intended to be used by
residential homeowners or professional, hired
operators. It is designed primarily for removing
snow from paved surfaces, such as driveways
and sidewalks, and other surfaces for traffic on
residential or commercial properties. It is not
designed for removing materials other than snow,
nor is a model with a pivoting scraper designed for
clearing off gravel surfaces.

Read this information carefully to learn how to operate
and maintain your product properly and to avoid injury
and product damage. You are responsible for operating
the product properly and safely.

You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a
dealer, or to register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready. Figure 1
identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.

Figure 1

1.

Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety alert symbol
(Figure 2), which signals a hazard that may cause serious
injury or death if you do not follow the recommended
precautions.

Figure 2

1.

Safety alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

Warning

CALIFORNIA

Proposition 65 Warning

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer, birth defects,

or other reproductive harm.

This spark ignition system complies with Canadian
ICES-002.

The enclosed

Engine Owner’s Manual

is supplied

for information regarding the US Environmental
Protection Agency (EPA) and the California
Emission Control Regulation of emission systems,
maintenance, and warranty. Replacements may be
ordered through the engine manufacturer.

© 2009—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

Содержание Power Max 38624

































Отзывы: