Toro groundsmaster 455-D Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 46

Toro groundsmaster 455-D Скачать руководство пользователя страница 31

Note

: The upper portion of the fan shroud may

be easily unbolted from the machine to
simplify cleaning.

D.

Install the rear screen and tighten the knobs.

IMPORTANT: Do not use water to clean
the engine, as damage may occur.

Figure 45

1. Oil

cooler

2.

Maintaining Cooling System—Capacity of the
system is 13 l (3.5 gal). Always protect the cooling
system with a 50/50 solution of water and Peugeot
recommended anti-freeze. DO NOT USE WATER
ONLY IN COOLING SYSTEM.

A.

After every 100 operating hours, tighten the
hose connections. Replace any deteriorated
hoses.

B.

After every 2 years or 1500 hours, drain and
flush the cooling system. Add anti-freeze
(refer to Check Cooling System).

Engine Fan Belt

Check the condition and tension of fan the belt (Fig. 46)
frequently. Inspect the belt every 800 hours of
operation.

1.

Proper tension will allow 6mm deflection on the
belt midway between the pulleys, when pressed
firmly with your thumb.

2.

If deflection exceeds 6mm, loosen the alternator
mounting bolts. Adjust alternator belt tension by
adjusting the tension screw. Check deflection of
the belt again to assure tension is correct.

Figure 46

1.

Fan belt

2. Adjusting

screw

Engine Timing Belt

Inspect the engine timing belt every 800 hours of
operation or yearly.

1.

Remove covers and check for a worn, cracked or
oil-soaked belt.

Note:

A new belt should be installed any time a belt is

removed or loosened.

Changing Hydraulic Oil

Change the hydraulic oil filter initially after the first 50
hours of operation; thereafter change the hydraulic oil
and filter after every 800 operating hours. If oil
becomes contaminated, contact your local TORO
distributor because the system must be flushed.
Contaminated oil looks milky or black when compared
to clean oil.

1.

Turn the engine off, release the hood latch and raise
the hood.

2.

Remove the drain plug from the rear of the
reservoir and hydraulic line from front of reservoir
(Fig. 47) and let hydraulic oil flow into the drain
pan. Reinstall and tighten the plug and line when

30

Before servicing or making adjustments to the
machine, stop engine and remove key from the switch.

WARNING

2

1

«
...
29
30
31
32
33
...
»

Содержание groundsmaster 455-D















































Отзывы:

Нет отзывов