Toro GreensPro 1240 Скачать руководство пользователя страница 76

Страница: 76 / 186

Adjusting Procedure for GreensPro 1240 (continued)

g241035

Figure 25

GreensPro 1240

Transmission

Hex nut

Damper

Bolt (2 each)

Linkage rod

Flat washer (4 each)

Transmission control arm

10.

Spacer (linkage arm)

Damper plate

11.

Spacer (damper plate)

Lock washer

12.

Locknut (2 each)

5. Start the engine and set the throttle to full engine speed.

6. For machines with a serial number above 315000000, have an assistant sit

in the operator’s seat and disengage the parking brake.

7. If the drive roller does not rotate, shut off the engine and attach the linkage

rod to the transmission control arm.

8. If the drive roller rotates, note the direction of drive roller rotation, then shut

off the engine and adjust the transmission control arm assembly as follows
(

Figure 26

A. Loosen the RTN (Return To Neutral) adjustment screw until the control

arm assembly can be rotated.

Hydraulic System: Adjustments

Page 5–30

GreensPro

™

1240/1260

14211SL Rev A

Содержание GreensPro 1240



























































































































































































Результаты поиска

Содержание GreensPro 1240

Отзывы:

Бренды по названию

Популярные бренды

Toro GreensPro 1240, Руководство по обслуживанию

Результаты поиска

Содержание GreensPro 1240

Отзывы:

Бренды по названию

Популярные бренды