Toro Greensmaster TriFlex 3400 Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 48

Toro Greensmaster TriFlex 3400 Series Скачать руководство пользователя страница 30

g014690

Figure 34

1.

Reel motor

3.

Cavity

2.

Spline shaft

4.

Motor retaining bar

7.

Mount a grass basket onto the basket hooks on
the suspension arm.

8.

Repeat this procedure for the other cutting units.

Removing the Cutting Units

1.

Park the machine on a clean level surface,
lower the cutting units to the ground until the
suspension hydraulics are fully extended, stop
the engine, and set the parking brake.

2.

Push the motor retaining bar out of the slots on
the motor towards the cutting unit and remove
the motor from the cutting unit.

g014605

Figure 35

1.

Reel motor

2.

Motor retaining bar

3.

Move the motor to the storage location on the
front of the suspension arm (

).

g014608

Figure 36

Note:

When sharpening, setting the

height-of-cut, or performing other maintenance
procedures on the cutting units, store the cutting
unit reel motors in the storage location on the
front of the suspension arms to prevent damage
to them.

Important:

Do not raise the suspension to

the transport position when the reel motors
are in the holders in the machine frame.
Damage to the motors or hoses could result.
If you must move the traction unit without
the cutting units installed, secure them to
the suspension arms using cable ties.

30

«
...
28
29
30
31
32
...
»

Содержание Greensmaster TriFlex 3400 Series

















































Отзывы:

Нет отзывов