Toro Greensmaster TriFlex 3400 Series Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 48

Toro Greensmaster TriFlex 3400 Series Скачать руководство пользователя страница 22

Specifications

Note:

Specifications and design are subject to

change without notice.

Width of cut

151 cm (59.5 inches)

Wheel tread

128 cm (50.5 inches)

Wheel base

123 cm (48.6 inches)

Overall length (w/baskets)

249 cm (98.0 inches)

Overall width

179 cm (70.62 inches)

Overall height

205 cm (80.83 inches)

Net Weight w/reels (11 Blade)

696 kg (1,535 lb)

Attachments/Accessories

A selection of Toro approved attachments and
accessories are available for use with the machine to
enhance and expand its capabilities. Contact your
Authorized Service Dealer or Distributor or go to
www.Toro.com for a list of all approved attachments
and accessories.

Operation

Note:

Determine the left and right sides of the

machine from the normal operating position.

Think Safety First

Please carefully read all of the safety instructions
and symbols in the safety section. Knowing this
information could help you or bystanders avoid injury.

The use of protective equipment, such as but
not limited to, for eyes, ears, feet, and head is
recommended.

Checking the Engine Oil

The engine is shipped with oil in the crankcase;
however, the oil level must be checked before and
after the engine is first started.

Crankcase capacity is approximately 3.7 L (3.9 quarts)
with the filter.

Use high-quality engine oil that meets the following
specifications:

•

API Classification Level Required: CH–4, CI–4 or
higher.

•

Preferred oil: SAE 10W–30

•

Alternate oil: SAE 15W–40

Toro Premium Engine oil is available from your
distributor in the 10W–30 viscosity. See the parts
catalog for part numbers.

Note:

The best time to check the engine oil is when

the engine is cool before it has been started for the
day. If it has already been run, allow the oil to drain
back down to the sump for at least 10 minutes before
checking. If the oil level is at or below the Add mark
on the dipstick, add oil to bring the oil level to the Full
mark.

Do not overfill

. If the oil level is between the

Full and Add marks, no oil addition is required.

Important:

Be sure to keep the engine oil level

between the upper and lower limits on the oil
gauge. Engine failure may occur as a result of
over filling or under filling the engine oil.

1.

Position the machine on a level surface.

2.

Remove the dipstick and wipe it with a clean rag
(

).

Important:

Make sure that the dipstick

is removed while filling the engine with
oil. When adding engine oil or filling oil,
there

must be

clearance between the oil fill

device and the oil fill hole in the valve cover
as shown in

. This clearance is

necessary to permit venting when filling,

22

«
...
20
21
22
23
24
...
»

Содержание Greensmaster TriFlex 3400 Series

















































Отзывы:

Нет отзывов