background image

Battery Warning Light

The light (

Figure 17

) glows if the battery charge is low.

Engine Oil Pressure Light

The light (

Figure 17

glows if the engine oil pressure

drops below a safe level.

Water Temperature Light

The light (

Figure 17

glows and the engine

automatically shuts down when the engine coolant
temperature gets too high. If the engine shuts down,
you can start the engine and drive the machine for 10
seconds before it will shutdown again, allowing you to
move the machine to a location where you can allow
it to cool down.

Service Indicator Light

The service indicator light (

Figure 17

) illuminates

when the machine sensors detect an issue with one
of the systems of the machine. If this light illuminates,
stop what you are doing and drive to a safe location
where you or a service technician can diagnose
the problem. For more information on diagnosing
system issues using the service indicator light, refer to

Diagnosing the Service Indicator Light (page 45)

.

Glow Plug Indicator Light

When the glow plug indicator light (

Figure 17

) is lit, it

indicates the glow plugs are on.

Note:

The glow plug indicator light may illuminate

for a short time after the engine has started; this is
normal.

Hour Meter

The hour meter (

Figure 18

indicates the total hours

the machine has operated. It starts to function
whenever the key switch is rotated to On.

g014600

Figure 18

1.

Hour meter

Parking Brake Lever

Pull up on the brake lever (

Figure 15

to set the

parking brake. Disengage it by pushing it forward and
down. Lock the parking brake any time you leave the
machine.

g014610

Figure 19

Backlap Lever

The backlap lever is located under the plastic cover to
the left of the seat. Use the backlap lever (

Figure 20

)

in conjunction with the raise/lower mow control lever
and the reel speed control for backlapping the reels.

20

 

Содержание Greensmaster TriFlex 3400 Series

















































Отзывы: