Toro 726TE Power Max страница 20 Скачать руководство пользователя

Страница: 20 / 24

3329-767

Problem

Corrective Action

Possible Causes

6. The fuel cap vent is restricted.

6. Remove the vent restriction or

replace the fuel cap.

Engine runs rough

1. The choke is in the On position.

1. Move the choke to the Off

position.

2. The fuel tank is nearly empty or

contains stale fuel.

2. Drain and fill the fuel tank with

fresh gasoline (not more than
30 days old). If the problem
persists, contact an Authorized
Service Dealer.

3. The spark plug wire is loose.

3. Connect the wire to the spark

plug.

4. The spark plug is pitted, fouled,

or the gap is incorrect.

4. Check the spark plug and

adjust the gap if necessary.
Replace the spark plug if it is
pitted, fouled, or cracked.

Engine runs, but the snowthrower
discharges snow poorly or not at
all

1. The snowthrower is moving too

fast to clear the snow.

1. Shift the snowthrower into a

lower gear.

2. You are trying to remove too

much snow per swath.

2. Reduce the amount of snow

removed for per swath.

3. You are trying to remove

extremely heavy or wet snow.

3. Don’t overload the snowthrower

with extremely heavy or wet
snow.

4. The discharge chute is

plugged.

4. Refer to Unclogging the

Discharge Chute on page 13.

5. The auger/impeller drive belt is

loose or is off the pulley.

5. Install and/or adjust the

auger/impeller drive belt; refer
to www.Toro.com for servicing
information or take the
snowthrower to an Authorized
Service Dealer.

6. The auger/impeller drive belt is

worn or broken.

6. Replace the auger/impeller

drive belt; refer to
www.Toro.com for servicing
information or take the
snowthrower to an Authorized
Service Dealer.

Snowthrower does not properly
clear the snow off the surface

1. The skids and/or the scraper

are not properly adjusted.

2. The tire pressure is uneven.

1. Adjust the skids and the

scraper.

2. Check the pressure in the tires

and adjust the pressure if
necessary.

Содержание 726TE Power Max

























Результаты поиска

Содержание 726TE Power Max

Отзывы:

Похожие инструкции для 726TE Power Max

Бренды по названию

Популярные бренды

Toro 726TE Power Max, Руководство оператора

Результаты поиска

Содержание 726TE Power Max

Отзывы:

Похожие инструкции для 726TE Power Max

Бренды по названию

Популярные бренды