Toro 44536 Скачать руководство пользователя страница 4

Страница: 4 / 16

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential
danger. Replace any decal that is damaged or lost.

93-7814

Entanglement hazard, belt—stay away from moving parts;
keep all guards and shields in place.

98-3110

Warning—read the

Operator’s Manual

and receive training.

Warning—wear hearing protection.

Thrown object hazard—wear eye protection and keep
bystanders a safe distance from the machine.

Cutting hazard of hand or foot—wait for moving parts to
stop.

105-0627

Warning—stop the engine, remove the ignition key before
leaving the machine and disconnect the power take–off
(PTO) shaft.

105-0628

Warning—do not operate the machine with power take-off
(PTO) at a greater angle than 15 degrees.

105-0668

105-0669

105-0698

Apply over decal 105-0707 for CE compliance

Warning—read the

Operator’s Manual

105-0707

105-0708

Warning—thrown object hazard; keep bystanders away
from machine.

Содержание 44536

















Результаты поиска

Содержание 44536

Отзывы:

Похожие инструкции для 44536

Бренды по названию

Популярные бренды

Toro 44536, Руководство оператора

Результаты поиска

Содержание 44536

Отзывы:

Похожие инструкции для 44536

Бренды по названию

Популярные бренды