Toro 30716, Руководство оператора

Страница: 4 / 24

4
•
The operator shall turn on flashing warning lights, if
provided, whenever traveling on a public road, except
where such use is prohibited by law.
Maintenance and Storage
•
Disengage drives, lower the cutting units, move traction
pedal to Neutral, set parking brake, stop engine and
remove key and disconnect spark plug wire. Wait for all
movement to stop before adjusting, cleaning or
repairing.
•
Clean grass and debris from cutting units, drives,
mufflers, and engine to help prevent fires. Clean up oil
or fuel spillage.
•
Let engine cool before storing and do not store near
flame.
•
Shut off fuel while storing or transporting. Do not store
fuel near flames or drain indoors.
•
Park machine on level ground. Never allow untrained
personnel to service machine.
•
Use jack stands to support components when required.
•
Carefully release pressure from components with stored
energy.
•
Disconnect battery or remove spark plug wire before
making any repairs. Disconnect the negative terminal
first and the positive last. Reconnect positive first and
negative last.
•
Use care when checking blades. Wrap the blades or
wear gloves, and use caution when servicing them.
Only replace blades. Never straighten or weld them.
•
Keep hands and feet away from moving parts. If
possible, do not make adjustments with the engine
running.
•
Charge batteries in an open well ventilated area, away
from spark and flames. Unplug charger before
connecting or disconnecting from battery. Wear
protective clothing and use insulated tools.
•
Keep all parts in good working condition and all
hardware tightened. Replace all worn or damaged
decals.
Toro Mower Safety
The following list contains safety information specific to
Toro products or other safety information that you must
know that is not included in the ANSI standards.
This product is capable of amputating hands and feet and
throwing objects. Always follow all safety instructions to
avoid serious injury or death.
Use of this product for purposes other than its intended use
could prove dangerous to user and bystanders.
Operation
•
Know how to stop the machine and engine quickly.
•
Always wear substantial shoes. Do not operate the
machine while wearing sandals, tennis shoes, or
sneakers.
•
Wearing safety shoes and long pants is advisable and
required by some local ordinances and insurance
regulations.
•
Fill fuel tank until level is 1 in. (25 mm) below the
bottom of the filler neck. Do not overfill.
•
Check the safety interlock switches daily for proper
operation. If a switch should fail, replace the switch
before operating the machine. After every two years,
replace all three interlock switches in the safety system,
regardless if they are working properly or not.
•
Pay attention when using the machine. To prevent loss
of control:
– Do not drive close to sand traps, ditches, creeks, or
other hazards.
– Avoid sudden stops and starts.
– Watch for traffic when near or crossing roads.
Always yield the right-of-way.
– Lower the cutting unit when going down slopes.
•
If the cutting unit discharge area ever plugs, shut the
engine off before removing the obstruction.
•
Cut grass slopes carefully. Do not start, stop, or turn
suddenly.
•
Do not touch the engine or muffler while the engine is
running or soon after it has stopped because these areas
could be hot enough to cause burns.
Maintenance and Storage
•
Check the blade mounting bolts frequently to be sure
that they are tightened to specification.
•
Make sure that all hydraulic line connectors are tight
and all hydraulic hoses and lines are in good condition
before applying pressure to the system.
•
Keep your body and hands away from pin hole leaks or
nozzles that eject hydraulic fluid under high pressure.
Use paper or cardboard, not your hands, to search for
leaks. Hydraulic fluid escaping under pressure can have
sufficient force to penetrate the skin and cause serious
injury.
•
Before disconnecting or performing any work on the
hydraulic system, all pressure in the system must be
relieved by stopping the engine and lowering the cutting
units to the ground.