Toro 136-4360 Скачать руководство пользователя страница 1

Form No. 3413-386 Rev A

Skid Plate Kit

Groundsmaster

®

4000 or 4100 Series Rotary Mower

Model No. 136-4360

Installation Instructions

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals known to the State of California to

cause cancer, birth defects, or reproductive harm.

Installation

1

Preparing the Machine

No Parts Required

Procedure

1.

Park the machine on a level surface.

2.

Lower the cutting units.

3.

Engage the parking brake.

4.

Shut off the engine and remove the key.

5.

Use a jack to raise the machine.

Note:

There are jacking points located at the front

and rear of the machine; refer to the

Operator’s Manual

for your machine.

DANGER

Mechanical or hydraulic jacks may fail to support
machine and cause a serious injury.

Use jack stands when supporting machine.

Do not use hydraulic jacks.

2

Installing the Skid Plates

Parts needed for this procedure:

2

Outer-rear skid plate

1

Rear skid plate

2

Front skid plate

4

Lock washer

4

Hex-socket screw

4

Spring-coil washer

4

Bolt (M10 x 30 mm)

4

Bolt (3/8-16 x 4 inches)

4

Flange nut

Installing the Rear Skid Plates

1.

Remove the existing hardware (4 bolts and 4 washers)
from the mount plate as shown in

Figure 1

.

© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA.

All Rights Reserved

*3413-386* A

 

Содержание 136-4360

Страница 1: ...at the front and rear of the machine refer to the Operator s Manual for your machine DANGER Mechanical or hydraulic jacks may fail to support machine and cause a serious injury Use jack stands when supporting machine Do not use hydraulic jacks 2 Installing the Skid Plates Parts needed for this procedure 2 Outer rear skid plate 1 Rear skid plate 2 Front skid plate 4 Lock washer 4 Hex socket screw 4...

Страница 2: ...m 3 Rear skid plate 2 Spring coil washer 3 Remove 2 bolts from the axle caps on both sides of the machine Figure 3 g207711 Figure 3 Right Side Shown 1 Bolt 3 Axle 2 Axle cap 4 Use 2 hex socket screws and 2 lock washers to secure the outer rear skid plates to the axle caps on both sides of the machine Figure 4 g204658 Figure 4 Right Side Shown 1 Hex socket screw 3 Outer rear skid plate 2 Lock washe...

Страница 3: ...11 Figure 5 Left Side Shown 1 Bolt existing hardware 5 Bolt 3 8 16 x 4 inches 2 Manifold 6 Front skid plate 3 Hub bracket 7 Flange nut 4 Nut existing hardware 2 Align the holes in a front skid plate with the holes in the manifold Figure 5 3 Use 2 bolts 3 8 16 x 4 inches and 2 flange nuts to secure the front skid plate to the hub bracket Figure 5 3 ...

Страница 4: ...l the other front skid plate to the right side of the machine Figure 6 g205112 Figure 6 Right Side Shown 1 Bolt existing hardware 5 Bolt 3 8 16 x 4 inches 2 Manifold 6 Front skid plate 3 Hub bracket 7 Flange nut 4 Nut existing hardware 4 ...

Отзывы: