background image

Light Switch

The light switch is located to the left of the steering
column (

Figure 10

). Use the light switch to illuminate

the headlights. Push the light switch up to turn on the
headlights. Push the light switch down to turn off the
lights.

g033954

Figure 10

1.

Light switch

2.

Hour meter

Hour Meter

The hour meter is located to the right of the light
switch (

Figure 10

). Use the hour meter to find out the

total number of engine hours. The hour meter starts to
function whenever you turn the key switch to the O

N

position, S

TART

position, or if the engine is running.

Note:

When the machine is running, the hour meter

blinks continuously, recording usage.

USB Power Point

The USB power point is located to the left of the
parking-brake lever (

Figure 6

). Use the power point

to power mobile devices.

Important:

When you are not using the USB

power point, insert the rubber plug to prevent
damage to the power point.

Fuel Gauge

The fuel gauge (

Figure 11

is located on the fuel tank

in the filler cap, at the left side of the machine. The
gauge displays the amount of fuel in the tank.

g033956

Figure 11

1.

Empty

4.

Full

2.

Half full

5.

Fuel-tank cap

3.

Needle

6.

Fuel gauge

Passenger Handholds

The passenger handholds are located on the outside
of each seat (

Figure 12

).

g033955

Figure 12

Passenger Side Shown

1.

Passenger handhold

14

 

Содержание 07059LT





























































Отзывы: