Toro 07059LT Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 60

Toro 07059LT Скачать руководство пользователя страница 15

Specifications

Note:

Specifications and design are subject to change without notice.

Base weight

397 kg (875 lb)

Rated capacity (on level ground)

544 kg (1,200 lb) total, including 90.7 kg (200 lb) operator and 91
kg (200 lb) passenger, load, accessories, and attachments

Gross vehicle weight (GVW)—on level ground

941 kg (2,075 lb) total, including all of the weights listed above

Maximum cargo capacity (on level ground)

363 kg (800 lb) total, including rear-mounted accessories

Maximum rear cargo-bed-accessory mount capacity

45 kg (100 lb) total

Tongue weight: 91 kg (200 lb)

Tow capacity

Gross trailer weight (GTW): 680 kg (1,500 lb)

Overall width

119 cm (47 inches)

Overall length

302 cm (119 inches)

Overall height

127.5 cm (50-3/16 inches)

21.6 cm (8-1/2 inches) at the front with no load or operator

Ground clearance

14 cm (5-1/2 inches) at the rear with no load or operator

Wheel base

220 cm (86-5/8 inches)

Front: 119 cm (47 inches)

Wheel tread (center line to center line)

Rear: 119 cm (47 inches)

Inside: 102 cm (40 inches)

Cargo bed length

Outside: 114.3 cm (45 inches)

Inside: 98 cm (38-1/2 inches)

Cargo bed width

Outside of the molded fenders: 107.3 cm (42-1/4 inches)

Cargo bed height

28 cm (11 inches) inside

Low idle: 1,250 to 1,350 rpm

Engine speed

High idle: 3,650 to 3,750 rpm

Attachments/Accessories

A selection of Toro approved attachments and accessories is available for use with the machine to enhance
and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to

www.Toro.com

for a list of all approved attachments and accessories.

To ensure optimum performance and continued safety certification of the machine, use only genuine Toro
replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be
dangerous, and such use could void the product warranty.

15

«
...
13
14
15
16
17
...
»

Содержание 07059LT





























































Отзывы:

Нет отзывов