Installing the Reel Drive Assembly
Note:
Refer to
during the procedure.
1. Use a press to install the 4 ball bearings (items 2 and 5 in
) into the
reel drive housing (6).
2. Secure the ball bearings with 2 retaining rings (item 3 and 4 in
)
into the reel drive housing (6).
g312504
Figure 17
1.
Retaining ring must be fully seated
2.
Press sleeve to shoulder
3. Install the bearing shield (11) into the reel drive housing (25).
Note:
Make sure that the carpet side of the bearing shield (11) is facing
towards the bearing.
4. Slide the reel shaft driver (13) into the reel drive housing (25).
5. Slide the spacer (9) into the reel drive housing (25).
6. Install the hipro key (12) onto the reel shaft driver (13). Apply anti-seize
lubricant on top of the key.
7. Install the reel pulley (8) onto the reel shaft driver (13). Secure the reel pulley
(8) with the lock nut (7).
8. Torque tighten the lock nut to
36.6 to 44.7 N∙m (27 to 33 ft-lb)
.
9. If removed, apply a coat of grease to the new O-ring (20) and install onto
the pivot sleeve.
10. Pack the internal splines of the reel shaft driven (22) with grease. Slide the
reel shaft driven (22) into the reel drive housing (25).
11. Slide the spacer (9) into the reel drive housing (25).
12. Install the hipro key (12) onto the reel shaft driven (22). Apply anti-seize
lubricant on top of the key.
13. Install the reel pulley (27) onto the reel shaft driven (22). Secure the reel
pulley (27) with the lock nut (7).
14. Torque tighten the lock nut to
36.6 to 44.7 N∙m (27 to 33 ft-lb)
.
15. If removed, install the bushing (29) into the idler arm (28).
16. If removed, use a press to install the 2 ball bearings (5) onto the idler arm
(28) and secure the ball bearings with a retaining ring (4).
17. Install and secure the idler am (28) into the reel drive housing (25) with
socket head screw (30) and nut (23).
18. Install the carriage bolt (6), washer (24) and nut (18) to the idler arm (28) and
reel drive housing (25). Do not tighten the nut (18).
19. Place the V-ring seal (21) into the reel drive housing (25).
20. Attach a new gasket (3) onto the reel drive housing (25).
Traction and Reel Drive Systems: Service and Repairs
Page 4–10
Greensmaster
®
eFlex 1021
20248SL Rev C
Содержание 04861
