manualshive.com logo in svg

Tormach ATC, Руководство пользователя

Поделиться
Скачать
Tormach ATC Скачать руководство пользователя страница 13

16. Identify wires 503 and 504 on the ATC Legacy Adapter Cable.

Then, route them through the wire troughs toward the DC-

BUS board.

Figure 2-36: DC-BUS board in the electrical cabinet.

17. Connect wire 503 to the TC+ terminal on the DC-BUS board.

18. Connect wire 504 to the TC- terminal on the DC-BUS board.

Rewire the ATC Board

1. Unlock and open the lid on the ATC main assembly with a

large, flat-blade screwdriver.

2. Identify the J10 connector on the ATC board, and then unplug

it from the board.

Figure 2-37: J10 connector on the ATC board.

3. Identify the loose ends of wires 403, 408, and GND.

Figure 2-38: Loose wires on the J10 connector from the ATC

board.

4. Remove the plastic wire protectors from the ferrule ends.

5. Use a small, flat-blade screwdriver to connect the following

wires to the J10 connector:

l

Wire 408 to pin 3

l

Wire 403 to pin 4

l

Wire GND to pin 5

6. Plug the J10 connector back in the ATC board.

7. Close the lid on the ATC main assembly and lock it.

Verify the Installation

1. Power on the machine and the PathPilot controller.

a. Turn the Main Disconnect switch to

ON

 on the side of the

electrical cabinet.

b. Twist out the Emergency Stop button on the operator

panel, which enables movement to the machine axes and

the spindle.

c. Press the Reset button on the operator panel.

d. Bring the machine out of reset and reference it.

2. If you have not yet done so, you must make sure that the

PathPilot controller is updated to the latest version of

PathPilot.

For information, see "Update PathPilot" (page 3).

Page 13

©Tormach® 2019
Specifications subject to change without notice.

tormach.com

TD10559: Owner's Guide: M ATC Retrofit for PCNC 1100 Series 3 (1119A)

TECHNICAL DOCUMENT

Содержание ATC























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды