Torini TC210 CLUBMAXX страница 3 Скачать руководство пользователя

Страница: 3 / 16

TORINI.COM.AU

RUN IN OIL

RACING OIL

Use for the first 1 to 1.5 hours

(Allows engine components to bed in)

Use only after run-in period

(Friction modified, anti-foaming formula)

SERIAL NUMBER LOCATION

APPROVED ENGINE OIL

PRODUCT PARAMETERS

KARTING AUSTRALIA HOMOLOGATED ENGINE OIL

The engine’s serial number, type and variant

number are all stamped on the crankcase.

You will need this information when ordering

parts and when making technical inquiries.

LOCATION OF

SERIAL NUMBER

ENGINE MODEL

TC210 CLUBMAXX

Engine type

Single cylinder, 4-Stroke, Forced Air Cooling, OHV25

Bore × stroke (mm)

70 × 55

Displacement (cc)

212

Compression ratio

8.5:1

Engine oil capacity (L)

0.55

Idle speed (r/min)

1800±100

Starting Mode

Recoil

Lubrication mode

Splash

Cooling system

Forced air cooling

Stopping mode

Grounding

Fuel

Premium Unleaded Petrol (as per KA rule book)

Shaft rotation (PTO)

Counterclockwise (seen from the end of output shaft)

Ignition system

T.C.I. Rev limited to 6,100 rpm

Ignition timing

25° BTDC (fixed)

Carburetor

Horizontal butterfly

Dry weight (kg)

Содержание TC210 CLUBMAXX

















Результаты поиска

Содержание TC210 CLUBMAXX

Отзывы:

Похожие инструкции для TC210 CLUBMAXX

Бренды по названию

Популярные бренды

Torini TC210 CLUBMAXX, Руководство пользователя

Результаты поиска

Содержание TC210 CLUBMAXX

Отзывы:

Похожие инструкции для TC210 CLUBMAXX

Бренды по названию

Популярные бренды