background image

Balanced XLR-F

GROUND

COLD (-)

HOT (+)

1

2

3

Balanced XLR-M

GROUND

HOT (+)

COLD (-)

1

2

3

TABLE OF CONTENTS

FEATURES ......................................................................................................................1

CONTROL ELEMENTS....................................................................................................2

stereo 2-way operation

......................................................................................................2

stereo 3-way operation

.....................................................................................................4

 

mono 4-way operation

.......................................................................................................6

CONNECTION

..................................................................................................9

 CABLES

SPECIFICATIONS..........................................................................................................10 

13 XOVER FREQ. button

     This button serves the knob of LOW/LOW-MID XOVER FREQ on the front-panel.
     Press  the button, and the knob ranges the frequency from  440 Hz to 9.3 kHz.
     Release the button, and the knob ranges the frequency from44 to 930Hz.
     

Always switch off the entire system before you press this button, as it produces 

         heavy interference noise that could damage your speakers and/or other equipment.

14 INPUT connector

     This balanced XLR Connecter is used to input the signal.

CONNECTION CABLES

     In this chapter you'll find the wiring diagrams for the connectors to be used with your 
     crossover.

     Take care of the connector cables, always holding them by the connectors and avoiding 
     knots and twists when coiling them: this gives the advantage of increasing their life and 
     reliability, which is always to your advantage.

     Periodically check that your cables are in good condition, that they are correctly wired 
     and that all their contacts are perfectly efficients: a great number of problems (faulty  

     contacts, ground hum. discharges, etc.) are caused entirely by using unsuitable or faulty 
     cables.  

9

9

Balanced JACK

GROUND

HOT (+)

COLD (-)

SLEEVE

RING

TIP

Содержание TXO-234 MK II









Отзывы: