background image

 

 

• Do not allow persons or children to remain in the automation operation area. 
• Keep radio control or other control devices out of  children’s reach, in order to avoid unintentional 
automation activation. 
• The user must avoid any attempt to carry out work or repair on the automation system, and always request 
the assistance of qualified personnel. 
• Anything which is not expressly provided for in the present instructions is not allowed. 
•  Before installing the gate opener, check that all moving part as well as the sliding gate is in good 
mechanical condition, correctly balanced and opens and closes properly. 
• Save these instructions for future use. 

Preparation for Installation 

Before proceeding to your opener installation, check if your gate structure is in accordance with the current 
standards, especially as follows: 
The gate sliding track is linear and horizontal. The wheels are suitable for use. The gate should be mounted 
and moved  freely. Check that the structure is sufficiently strong and rigid, and that its dimensions and 
weights conform to those listed in the specifications table of this document. Make sure that the gate is plumb 
and level. The fence posts must be mounted in concrete. The gate does not bind or drag on the ground. 
• The gate manual operation can be carried out smoothly along its entire run, and there is no excessive side 
slipping. 
• The opening and closing gate stops are positioned. 

 

WARNING: 

Remember that control devices are intended to facilitate gate operation, but can not 

solve problems due to any defects or deficiency resulting from failure to carry out correct installation or 
maintenance. Take the product out of its packing and inspect it for damage. Should it be damaged, contact 
your dealer. Remember to dispose of its components (cardboard, polystyrene, nylon, etc.) according to the 
current prescriptions. 

Refer to the following Figures for gate installation. 

 

 
 
 
 
 
 
 
 
 

In sake of safety, a positive stop must be mounted on the two end of ground track. 

 

 

Содержание RK2600


















Отзывы: