Topcon Pocket-3D Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 316

Topcon Pocket-3D Скачать руководство пользователя страница 66

Setup Menu

Pocket-3D Reference Guide

2-20

•

To calibrate the transmitter

– see “TX Calibration” on



•

To load transmitter data for the first time

– tap

Download

to

retrieve calibration data from the connected transmitter.
The download is complete when the firmware version displays in
the

Firmware

column.

Figure 2-28. View Transmitters Loaded into Pocket-3D

The Channel tab

displays the following transmitter information

(Figure 2-29 on page 2-21):

• Channel – the channel the transmitter is using.
• Transmitter – the ID of the transmitter.
• ControlPt. – the control point over which the transmitter is set up.
• Height – the height of the transmitter.
•

Edit Channel

– see “Edit Channel” on page 2-23.

«
...
64
65
66
67
68
...
»

Содержание Pocket-3D





























































































































































































































































































































Отзывы:

Нет отзывов