Topcon Pocket-3D Скачать руководство пользователя страница 43

Страница: 43 / 316

GPS Status Information

P/N 7010-0628

1-21

Magellan, Trimble, etc. This helps with correct RTK operation
where GLONASS is used at the base and rover where the base is
not a Topcon base.

Figure 1-25. Advanced Tab

Total Station Status

While in total station control, to view total station information,
change search area or change track sensitivity and speed, press the

Total Station status

button on the toolbar (Figure 1-26 on



page 1-22).
The color of the button and state of the hardware symbol indicates the
status of the system.

• Background color – green means the entire system communicates

with Pocket-3D; red means all or some part of the system is not
communicating with Pocket-3D.

• Hardware symbol state – if the symbol is crossed out, the

corresponding sensor/receiver is not available.

The instrument selected during equipment setup determines the tabs
that display.

NOTE

For non-robotic total stations, the prism symbol will
remain crossed out.

Select a Base

manufacturer from the

drop-down list

Содержание Pocket-3D





























































































































































































































































































































Результаты поиска

Содержание Pocket-3D

Отзывы:

Topcon Pocket-3D, Справочное руководство, Страница: 43 / 316

Результаты поиска

Содержание Pocket-3D

Отзывы: