Topcon Pocket-3D Скачать руководство пользователя страница 240

Страница: 240 / 316

Survey Menu

Pocket-3D Reference Guide

4-14

On the Topo-shot tab,

select the desired options for topo-shot

measurements, then press

Ok (

Figure 4-22 on page 4-15

)

• Prompt for pt. details – enable to prompt for point details every

time a topo-shot is measured.

– Before: enable this option to prompt for point details before

the topo-shot is measured.

– After: enable this option to prompt for point details after the

topo-shot is measured.

• Minimum requirements – the following options define the

minimum requirements for each topo-shot measured.

– Duration (secs): enter the minimum time in secon45ds

desired for each topo-shot.

– H. Precision: enter the minimum GPS+ horizontal precision

desired for each topo-shot.

– V. Precision: enter the minimum GPS+ vertical precision

desired for each topo-shot.

• Press ENTER to measure – enable to use the Enter key on the

controller’s casing (below the display screen) to start the
measurement on each topo-shot.

• Require RTK Initialized – enable to allow measurements in a

float/autonomous solution.

• Require mmGPS Signal – allows for only mmGPS+ initialized

measurements. If the solution is initialized only (rather than
mmGPS initialized), the shot will not be accepted. This option
allows measurements in a float/autonomous solution.

Содержание Pocket-3D





























































































































































































































































































































Результаты поиска

Содержание Pocket-3D

Отзывы:

Topcon Pocket-3D, Справочное руководство, Страница: 240 / 316

Результаты поиска

Содержание Pocket-3D

Отзывы: