Topcon Pocket-3D Скачать руководство пользователя страница 198

Страница: 198 / 316

Data Menu

Pocket-3D Reference Guide

3-88

•

From Point

– press to select the point from which to begin.

•

To Point

– press to select the point from which to end.

• Length P1-P2 – displays the length between the two selected

points.

• Azimuth Pl-P2 – displays the azimuth from point 1 to point 2



(0° being at the top of the screen).

• Distance from P1 – enter the distance desired for the offset

beyond point 1, then press

• Distance beyond P2 – enter the distance desired for the offset

beyond point 2, then press

• Offset from line P1-P2 – enter the offset distance desired from the

line created from Point 1 to Point 2, then press

Figure 3-131. Create Point Dialog Box

The view screen displays the baseline created from the two points
and the newly created point (Figure 3-132).

• Press the

+/-

buttons to zoom in or out on the image, or press

down on the screen and drag the image around.

• Press

Next

to continue.

Содержание Pocket-3D





























































































































































































































































































































Результаты поиска

Содержание Pocket-3D

Отзывы:

Topcon Pocket-3D, Справочное руководство, Страница: 198 / 316

Результаты поиска

Содержание Pocket-3D

Отзывы: