Topcon Pocket-3D Скачать руководство пользователя страница 145

Страница: 145 / 316

Surface

P/N 7010-0628

3-35

above for details.

Figure 3-50. Template Definitions / Add Templates Dialog Boxes

•

Delete

– on the

Template definition

s dialog box (Figure 3-48 on

page 3-34), press

Delete

to remove the selected template.

On the

add templates

dialog box (Figure 3-51 on page 3-36), press

Add

to enter a template and its respective information, then press

to save.

• Template name – enter in the name of the Template.
• Template elements – on the

Template elements

dialog box,

template elements can be created, edited, or deleted. After
creating template elements press

to continue (Figure 3-52 on

page 3-37).

•

Add

– On the

template elements

dialog box, press

Add

to enter a

template element and it’s respective information, then press

save the information.

•

Edit

– on the

template elements

dialog box, press

Edit

to edit the

selected element. See the “Add” bullet for details.

•

Delete

– on the

template elements

dialog box, press

Delete

remove the selected element.

Содержание Pocket-3D





























































































































































































































































































































Результаты поиска

Содержание Pocket-3D

Отзывы:

Topcon Pocket-3D, Справочное руководство, Страница: 145 / 316

Результаты поиска

Содержание Pocket-3D

Отзывы: