Topcon Pocket-3D Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 316

Topcon Pocket-3D Скачать руководство пользователя страница 142

Data Menu

Pocket-3D Reference Guide

3-32

Figure 3-46. Create a Vertical Profile

On the

Vertical profile

dialog box, create your vertical profiles:

•

Add

– press to enter an element and its respective information,

then press

Ok

to save the information (Figure 3-47 on page 3-

33).

– Element: select the type of element; either Curve or Point.
– Station: enter the station number.
– Elevation: enter the elevation of the element.
–

Observe

: press

Observe

to measure the element, instead of

manually entering in the values.

– Station of IP: enter the station number for the IP (PI).
– Elevation of PI: enter the elevation for the PI.
– Curve Length: enter the length of the curve.
– Grade Start VC: enter the grade at the start of the vertical

curve.

– Grade End VC: enter the grade at the end of the vertical

curve.

«
...
140
141
142
143
144
...
»

Содержание Pocket-3D





























































































































































































































































































































Отзывы:

Нет отзывов