manualshive.com logo in svg

Top Speed Tunnel Hull, Инструкция по эксплуатации

Поделиться
Скачать
Top Speed Tunnel Hull Скачать руководство пользователя страница 1

CONGRATULATIONS!

Thank you for choosing the Top Speed Tunnel Hull. This boat has been designed for the intermediate
to advanced boater looking for an easy to assemble, yet high performance tunnel hull. The assembly
is quick and easy, with no special tools or modeling skills required. The Top Speed is a fast, high
performance boat that can be adjusted to differing water conditions to perform at its peak potential.

Please read through this instruction manual in its entirety before beginning assembly. It contains
important instructions and warnings concerning the assembly and use of this model.

Warning! THIS MODEL IS NOT A TOY!

Assembly and operation of this boat must be done by or under the direct supervision of a responsible

adult. If not handled correctly, this model is capable of inflicting serious bodily harm. It is your responsibility
and yours alone to assemble this boat correctly, properly install all R/C components and test and operate it

in a safe and responsible manner.

GPMZ0261 FOR KITS GPMB1050/1055

Entire Contents © Copyright 1999

INSTRUCTION

MANUAL

TM

Содержание Tunnel Hull

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды